Your trusty jigsaw is the best tool to help you cut plywood. You will be able to cut plywood with ease after a few practice sessions. This blog will show you how to use your jigsaw to make plywood cuts like a pro.
You don’t need a jigsaw to make plywood cuts. You can quickly make precise cuts with just a bit of practice.
Which type of blade should I use?
Perforated blades are best for cutting plywood. Perforated blades have many tiny holes that will smoothen your cut lines when they come into contact with wood. Standard blades have a straight edge without any holes or slits, so they don’t have the same smoothness.
This blog post will show you how to use your jigsaw to make plywood like a professional.
Step 1 – Make sure you have all the tools
Jigsaw Sander Phillips Head Screwdriver Rubber Mallet Several spare blades for your safety glasses and ear plugs
Before you start, make sure you have all the tools you need.
Step 2 – Mark Your Cut Line
Mark your lines to ensure that your plywood cuts are smooth and precise. Measure the plywood piece you wish to cut. This will help you determine the length of the cuts along each side. Straight lines can be drawn with a pencil or a pen.
A marker is the best choice for best results. It won’t smudge if it gets wet from sawdust. Both lines should be drawn on the plywood’s face. Make sure that they meet at the corners where the two lengths meet.
Step 3 – Determine Cut Locations
Once you have drawn your lines, it is time to put together the jigsaw puzzle. Begin by aligning the blade of your Jigsaw with one of the lines. The blade should be located near the area where you will make your first cut. It should be centered between the marks or aligned with the mark. This will ensure that the saw cuts straight across the length of the cut when you push down. Once you are satisfied with the look of your saw, tighten the knob on the back to ensure there is no room for error. It can cause a delay in your cutting line if there is too much slack.
Step 4 – Start cutting
Once you are ready to go, plug the jigsaw in and let’s get started! Make sure your hands are secure by holding the tool with both your thumbs. Wrap your four fingers around the handle. Then press down on trigger until the trigger feels resistance. You can now move along the cut line. To make smooth cuts, maintain constant pressure. Don’t worry if you get some spray or blowout underneath the area where the jigsaw blades are cutting through the wood.
Step 5 – Finish the Cut Line
Once you have cut most of the board out, put your jigsaw down and get a 120-grit sandpaper sander. Connect it to the machine and run it slowly along the cut line, until it reaches the end. If you encounter resistance when cutting, you can flip the board over and make another cut where it is still connected.
Step 6 – Mark Cut Location On The Back Of Plywood Article
After you have created a smooth line, switch to a drill that has a countersink bit. The tip of the bit should be placed right where the jigsaw blade cut through the wood. It is important to align the bit perfectly. Take your time and make sure you are satisfied with it before you press the trigger. You don’t need to go too deep. A standard screw-in hole should suffice for this hole. It shouldn’t poke out the back of your board.
Step 7 – Insert screws in the holes and begin securing board down
Next, drill the two holes into the plywood. Make sure you only use the recommended screw size and type for this job. If in doubt, check with your local hardware shop before heading out. Once you have inserted both screws, you can begin assembling all the pieces of wood.
Step 8 – Lay Plywood Pieces Wherever You Want It
After the plywood pieces are securely attached, it’s time to place them exactly where you want. It is a process of trial and error, so be patient and take your time. This refers to the board’s edges looking as beautiful as possible.
Step 9 – Trace and Cut a Top Panel To Fit Overboard
Once you have all of your measurements taken and checked, take one more sheet plywood and mark the dimensions on that piece. Place the plywood boards in a row, with the cut sides facing upwards. Next, place the new board on top.
Step 10 – Cut the Panel and Drill Some Holes
After you have marked your measurements, grab your jigsaw. You can cut around the entire panel from all four sides. Don’t rush this job. Make sure you are not cutting beyond your line by more than 1/10 cm.
Tips and Tricks
- Cut exactly between the two supports. This will make it easier for you to remove the plywood.
- When you are working on angle cuts, slow down your saw. You won’t burn your edge when you cut into an angle from the outside.
- When cutting along the ends of the aboard, make sure the blade is at the maximum depth. You won’t get the cut you want if you don’t.
Final Thoughts
This is all you need to know about plywood cutting with a Jigsaw. You should be able make precise cuts with the right blade after some practice. You’ll soon be able tackle any woodworking project you get. Take your time, pay attention and take your time.
